MDC’s Kwik-Flange™ ISO KF components are
an economical system of reusable interfacing stainless steel vacuum fittings for
tube sizes ranging from 1/2" through 2"
diameters. These flanges can operate in high vacuum environments to pressures in the
1x10-8 Torr range. The Kwik-Flange™ ISO KF flange system is ideally suited for
applications requiring rapid and frequent assembly and disassembly. MDC ISO KF
flanges comply with all ISO specifications for vacuum mounting hardware and are
compatible with most third party ISO KF flanges and components.
Kwik-Flange ISO KF Assembly
Vacuum rated to 1x10-8 Torr
Bakeable to 150°C
Fast connect and disconnect
Economical reusable fittings
Rotatable bolt ring adapter
Elastomer gasket seal
Varied fastening methods
ISO KF and LF compatible
Specialty fittings available
Type 304 stainless steel
Viton®, Buna-N® or Silicone elastomer
Clamps, hinged & bulkhead
Hinged with 10-32 thread
Hexagonal head bolts, 10-32 thread
Clamp: Finger tight
Bolts: 7-10 lb-ft
1/4 lb maximum
1.18 OD x .680 ID maximum
The MDC Kwik-Flange™ ISO KF family of modular building-block components includes
all of the commonly used standard hardware and fittings. Virtually all standard MDC
feedthroughs and accessories are available for use with Kwik-Flange™ ISO KF flanges.
Reducer flanges are available to connect different size ISO components. This catalog
includes ISO KF and ISO LF reducer flanges for KF to KF, KF to LF and LF to LF flange
combinations. Hybrid adapters are available to connect ISO KF components to other non
ISO vacuum fittings and mounts. These include Del-Seal™ CF metal seal flanges,
ANSI ASA flanges, Swagelok® compression tube fittings and VCR® metal gasket tube
fittings, national pipe thread fitting, etc.
MDC Kwik-Flange™ ISO KF flanges are available in four standard maximum tube
sizes including 3/4", 1", 1-1/2" and 2" diameters. Each of these basic flanges are
then offered in weldable formats, prepped for varying smaller tube sizes. Typically, U.S.
tube sizes are specified in inches and identified by their outside diameters. MDC
standard ISO KF flange size designations are as follows... K075 for 0.75", K100 for 1.00",
K150 for 1.50" and K200 for 2.00" tube diameters. It’s worth mentioning that, with
the exception of the centering ring locater diameter, three of the ISO KF flanges
depicted in the diagram below, namely NW 10, 20 and 32, are identical to NW 16, 25
and 40 respectively. These latter flanges being the standard for all of MDC’s ISO KF
fitted products equipment fitted with NW 10, 20 and 32 flanges can mate them with MDC NW 16, 25
and 40, respectively, by using MDC’s reducer centering ring. The reducer centering ring is
constructed with two different size tubular rims or extensions which mate with the
respective flange size centering ring locater groove or counterbore.
For product listing, features and
specifications click on links below
As previously noted, Kwik-Flange™ ISO KF flanges provide a vacuum mount interface
for tube diameters up to 2.00 inches. For tube diameters above this, Large-Flange™
ISO LF flanges are used. Kwik-Flange™ and Large-Flange™ flanges are part of one and
the same family of ISO standard elastomer sealed mounts. Together they provide a
complete range of vacuum mounts for 0.75 to 20.0 inch diameter tubes. ISO KF and LF
sealing mechanisms are similar but their fastening and clamping methods differ. Due
to the wide variation of references used by ISO flange manufacturers, MDC emphasizes
the use of the standard ISO NW reference. Note that for all practical purposes, NW and
DN references are identical. Large-Flange™ ISO LF flanges are presented immediately
after the Kwik-Flange™ ISO KF flanges.
In general, MDC components compare with international components using an
inch-to millimeter ratio. U.S. sizes refer to a tube’s outside diameter, whereas international sizes
refer to a tube’s inside diameter. The chart shown on right gives a quick comparison between
inch and metric ISO flange sizes.
Please select your country in order to have the best shopping experience on our website. Your country selection will determine what product catalog you see, the currency, and other information that pertains to your exact location. For the best service, it is very important that you select the correct country.
Submitting Please Wait..
If you choose to login or create an account, then the website country mode you will be shown will be based off of the country you entered in your account contact information. You can edit your country in your account contact information at any time.